PLC BOARD เหมาะสำหรับท่านที่ต้องการทดลอง เขียนโปรแกรม PLC และใช้งานจริง ในโปรเจคเล็ก ๆ ครับ

          ตัวบอร์ต ติดต่อ ผ่าน RS232 มีสาย USBtoSerial ติดต่อได้โดยตรง สามารถเขียน โปรแกรมใน GX Developer ของ PLC Mitsubishi  ได้เหมือนกันเขียนด้วย PLC จริง ๆ ครับ ใช้งาน Input Output Sensor และ Solenoid ขับ Stepping Servo Motor ได้เหมือน PLC ไฟเลี้ยงแรงดัน 24 V. ได้โดยตรง ใช้งานได้เทียบเท่าคำสั่ง PLC Mitsubishi FX Series  ติดต่อ HMI ผ่าน RS232 ได้เลย ครับ

              สามารถใช้งานในโหมด  ONLINE MONITOR ได้ UPLOAD DOWNLOAD ได้   มีหน่วยความจำเหมือนกัน PLC Mitsubishi

(1). RS no agreement communication (mitsubishi basic),
(2). Modbus RTU master-slave protocol (convenient support temperature control meter, frequency converter communication),
(3). Modbus ASCII master-slave agreement.

Support A/B phase high speed counting input, support Y0 Y1, high speed output (transistor), support and deceleration, with absolute positioning relative positioning.

Don't need software conversion, direct download monitoring and normal PLC as download mode
Can directly use mitsubishi programming software GX Developer or GX Works2 programming, download, debugging and monitoring.

Instruction descriptions:

Write Program, parameters, comments
Read Program, parameters, comments
Check Program, parameters, comments
Computer monitoring function (convenient debugging)
Soft element batch function
Soft element landing function
Soft element test function
Clear memory function
Connection text HMI function (baud rate 9600, data bit 7, parity bit, even parity check (even), stop bit 1)
Connection touch screen Display function (baud rate 9600, data bit 7, parity bit, even parity check (even), stop bit 1)
Data retention during power-down  function

Supports command sets special soft element:
M8000 (operation monitoring contactoror), M8001 (operation monitoring back contactoror).
M8002 (initialization pulse contactor), M8003 (initialization pulse reverse contactor).
M8004 (error indication contactor).
M8011 (10 milliseconds clock pulse), M8012 (100 milliseconds clock pulse), M8013 (1 seconds the clock pulse), M8014 (1 time sharing the clock pulse).
M8020 (zero mark), M8021 (borrow mark), M8022 (carry flag).
M8029 (instruction execution end mark).
M8033 (memory keep contactor).
M8034 (banned output contactor).
More reference FX2N series.

Basic instruction:

LD, LDI, AND, ANI, OR, ORI, OUT, (OUTT, OUTC), SET, RST, ANB, ORB, MPS, MRD.
MPP, INV, the LDP, LDF, ANDP, ANDF, ORP, ORF, RET, OUTM, SETM, RSTM, OUTS, SETS,
RSTS, PLS, PLF, MC, MCR, PI, END

Step-by-step instruction:

STL: support maximum 8 road parallel branch, different state number can have a double coil.
contactor compare instruction:

LD > =, LD < =, LD >, LD < < >, LD, LD =, AND > =, AND < =, AND >, AND < < >, AND, AND, OR AND = > =, OR < =, OR >, < > OR < AND, OR, OR =.
Transfer and compare instruction:

MOV, CML, XCH, BCD, BIN, CMP, ZCP, FMOV. SMOV. BMOV.
Arithmetic instruction:

ADD, SUB, MUL, DIV, INC, DEC, WAND, WOR, WXOR, NEG.
Cyclic shift instruction:

SFTR, SFTL, SFWR, SFRD.
Data processing instruction:

ZRST, DECO, ENCO.
Program flow instruction:

CJ, CALL, SRET, IRET, EI, DI, FEND, WDT, FOR, NEXT.
Convenient instruction:

IST, ABSD, INCD, ALT, RAMP,
High speed processing instruction:

REF, REFF, MTR, HSCS, HSCR, SPD, PLSY, PWM, PLSR (two way pulse output, Y0 Y1, mouth).
Peripheral equipment I/O port:

DSW, SEGL, FROM, TO.
Peripheral equipment SER instruction:

RS, PRUN, ASCI, HEX, CCD, VRRD, VRSC, PID.
 Clock operation:

TCMP, TZCP, TADD, TSUB, TRD, TWR, HOUR.

Support 32-bit instruction!
Soft element power-down Data retention, application refers to this and mitsubishi FX1N compatible,
At present only two instructions does not be supported (HSCS, HSCR)

Special soft element:
M8000 (operation monitoring contactor), M8001 (operation monitoring back contactor).
M8002 (initialization pulse contactor), M8003 (initialization pulse reverse contactor)
M8004 (error indication contactor).
M8011 (10 milliseconds clock pulse), M8012 (100 milliseconds clock pulse), M8013 (1 seconds the clock pulse), M8014 (1 time sharing the clock pulse).
M8020 (zero mark), M8021 (borrow mark), M8022 (carry flag).
M8029 (instruction execution end mark).
M8033 (memory keep contactor).
M8034 (banned output contactor).
M8200 - M8203 (C200 - C203 count direction).
M8235 (C235 count direction).
D8000 (monitoring timer setting).
D8012 (maximum scanning time).
D8140 (Y0 pulse output count register)
D8142 (Y1 pulse output count register)
Maximum memory capacity: 8000 steps.